Trawbreaga Bay Light Railway
  • Home
  • Locomotives
  • Railcars
  • Rolling Stock
    • Coaching Stock
    • Goods Wagons
    • Private Owner Wagons
    • Service Vehicles
  • In the Works
    • Workshop Blog
    • Building CVBT No.3
    • Building the Drewry Railcar
    • Kerr Stuart Diesel
    • Building the S&S Coaches
    • Building the New TBLR
    • Building the Original Railway
  • Gallery
  • Track Plan
  • Structures
  • Withdrawn Locomotives
  • Gallery Archive
  • Structures Archive

Modifying Roundhouse Millie Part 4 - conclusion

12/9/2012

0 Comments

 
I was less than impressed with the finish I got from the Precision Paint. This despite the fact that I used a good quality brush and I had stirred the paint thoroughly for a good five minutes with a spatula. "Why didn't you spray it?" I hear you ask. I try to avoid spray painting wherever possible as the spray paint gets everywhere, even when using a homemade spray booth (cardboard box). Spraying is usually carried out in the garage or rarely outdoors if it is a calm day, this is a rare occurrence as I live beside the sea and it is almost always windy. Anyway, I prefer to paint with a brush in the comfort of my own home whenever possible. I remember repainting a Mamod loco by hand with Precision Paint about 30 years ago and got good results by rubbing down with wet and dry paper between coats.

I rubbed the offending paint finish down with wet wet & dry paper until the surface was smooth again. I then applied two coats of Humbrol 33 matt black enamel. When the second coat was dry I applied the company crests to the tank sides and finally I applied two coats of Humbrol satin varnish from an aerosol spray can. I sprayed the varnish outdoors as it was a very warm and unusually calm day! The resulting finish is not perfect but it is perfectly acceptable for a hard working loco which is not intended to be a showcase model.
Works plates were fixed to the tank sides before joining them to the cab front. The side tanks and cab front were then attached to the chassis using the existing fixing lugs and 6BA screws.

The loco is not modelled on any particular prototype but with its slab sided tanks and flat smokebox sides, it bears a passing resemblance to something built by Thomas Green and Son of Leeds. For that reason I used a set of Thomas Green works plates that I had originally intended for a model of their tram engine, works number 169 that was built for the Dublin and Lucan Tramway in 1892.  I decided a while ago not to build the tram engine and I could not let the plates go to waste. The Dublin and Lucan sold the tram loco to a contractor in 1896 and it was used on a railway building project in Donegal, either the CDR Letterkenny line or possibly the L&LSR Buncrana to Carndonagh extension. So with a bit of a leap of the imagination one of the contractor's  locos could have been sold on to the TBLR on completion of the contract.

All TBLR steam locos have a crew of two. The driver is a Brandbright 'Roger' correctly scaled at 1:20. Roger has had his ponytail cut off and more radically his left hand was also amputated to avoid obstructing the gas filler valve. He came off better than the fireman, a slightly underscale Bachmann G scale figure, as well as having the end of his shovel removed he was amputated at the waist and glued to the top of the gas tank with silicone adhesive. Roger was also stuck in place before the cab rear (with number plates applied) and roof were fixed in place followed by the rear buffer beam.

Finally a pair of re-railing jacks and a cast toolbox (from Roundhouse) were glued to the front running plate left and right hand sides respectively. These hide the fixing screws on the front of the side tanks.

No.6 (as she is now known) really looks at home on the railway now and is a powerful and reliaable runner. The sound produced by the chuff pipe is very realistic when the loco is working hard.


Picture
Millie before modification
Picture
No.6 - Transformation complete
0 Comments

Modifying Roundhouse Millie Part 3

2/9/2012

0 Comments

 
The buffer beams and coupling mounts were given several coats of Royal Mail red on the outward facing sides. The rear of the buffer beams were painted black. Couplings and vacuum pipes were fixed in place and the beams were then fitted back on the loco. The rear one is only temporarily in place as it will need to be removed again to allow fitting of the cab.
The smokebox and chimney was then given two coats of matt black paint before being re-fitted to the boiler front. The loco was then given a steam test to check that all joints were steam tight and to audition the effect from the chuff pipe (which is very impressive).
It was then time to turn my attention to the new cab and the original tank sides. The paint scheme is dull black for this loco so I ordered the Roundhouse replacement cab in black. This is however in a gloss finish so I gave the paintwork a good rub down with wet and dry paper, wet, to prepare it for  painting. I also did this with the original blue tank sides after giving them a thorough de-greasing.
Next I gave the cab interior two coats of satin cream enamel paint. The cab roof was also rubbed down and has received two coats of matt black. The cab and tank sides have just had a first coat of Precision dull black applied by brush and this will be rubbed down when dry to prepare the surfaces for the next coat of paint.
Picture
The loco ready for a steam test
Picture
The cab components. Roof and cab interior have been painted
Picture
The original tank sides prepared for painting
0 Comments

    Archives

    September 2018
    August 2018
    May 2018
    March 2018
    June 2017
    April 2017
    March 2017
    August 2016
    July 2016
    June 2016
    May 2016
    April 2016
    March 2016
    February 2016
    January 2016
    December 2015
    November 2015
    October 2015
    September 2015
    August 2015
    July 2015
    June 2015
    May 2015
    April 2015
    March 2015
    February 2015
    January 2015
    December 2014
    November 2014
    October 2014
    September 2014
    August 2014
    July 2014
    June 2014
    August 2013
    July 2013
    April 2013
    February 2013
    January 2013
    September 2012
    August 2012
    June 2012
    May 2012
    April 2012
    March 2012
    February 2012

    Categories

    All
    Accucraft Conversion
    Battery Packs
    Brake Vans
    Buildings
    Building T & D Coach 13
    Cattle Wagons
    Christmas
    Demolition
    Extending The Railway
    Gas Firing
    Lamp Irons
    Lineside
    Radio Control
    Railcar Gearboxes
    Roundhouse Locos
    Roundhouse Millie
    Rust
    Service Vehicles
    Tram Locos
    Wagon Loads
    Wagons

    RSS Feed